katybellabug

I suspect it must have something to do with the button plackets and how they fold back. Can you post a picture?

Thank goodness you spotted that as it looks like you would have been missing quite a bit of width too, and had a very tight crotch seam! (Eek). Hope you can piece the fabric and make it work.

Oh Heidi, how frustrating, and how very odd….
I don’t have the digital pattern but have just got my paper pattern out to check:
the length of the inseam on the pattern piece from the crotch edge to the hem edge is 18cm / 7&1/8″ on both the front and back shorts and this is true for all sizes.
So, it’s not the case that you’ve accidentally traced…[Read more]

I’ve had to do that before. 😉
A little join in your lining won’t matter.

Let me get this right, you’re not planning on the skirt being reversible are you? If yes, the you need to consider leaving the pockets off.
If not, then construct the outer skirt and pockets as per the instructions, then construct your skirt lining. You need to have made the lining pieces so that they don’t have pockets. If you’re unsure of how to…[Read more]

Hi Victoria, have you seen the errata note for this pattern?
If you go the pattern in the shop then you’ll see the tabs for details, photos, reviews etc There’s a tab for errata.
I’ve seen this shirt a few times and found it works fine, but when the pattern first came out there were a number of people who experienced difficulty fitting the collar…[Read more]

Thanks Heidi, I knew it was there somewhere but was too busy to hit the search.
Cybele, I think those sleeves need a flounce not a ruffle in order to get the fluttery effect you’re after.

So,…. You’re planning on keeping the dropped shoulder sleeve head the same, just changing the attached sleeve portion, is that right?
I wonder if it might be better to keep it single layer and have a narrow or rolled hem on the end of the sleeve. A double layer might be too heavy to “flutter” – flappy and saggy are not really what you want…[Read more]

You certainly can fit a hood into the Forest Path Cape. I’ve added a collar, and I know someone’s added a full hood to the Woodland Stroll Cape (the grown up version).
But….. What you really need is the Red Riding Hood Cape from the book Little Things to Sew. It has a hood, single front button closure, lovely little hand slits and really nice…[Read more]

Hi @ischyrus Steven. I wonder if it would be as simple as sewing the collar stand without the collar.
That may give more of a Mandarin collar look rather than the image you’ve shown.
That image has the collar band lying very flat and almost looks like the neckline is finished with a bias.
If you use scraps (just cut a neckline and shoulders) you…[Read more]

Short answer, yes. Long answer: I seem to recall another thread where this was discussed at length.
I’ve only made one hide and seek with the notch but it was a linen type weave and on the very first washing it all frayed around that notch. Maybe I’d clipped too close, but that was certainly a fabric where interfacing both sides of the yoke would…[Read more]

I find they flatten out just fine. Much better in fact than a baking paper tracing, or the printer paper if you’re using a PDF pattern. – one of the reasons I even trace home printed PDF patterns.
Just whatever you do, do not (NOT!) try and iron the trace and Toile!! 🙂

Hi Kathy @kjmcinerny , sorry for the late reply.
I tend to trace all my patterns, including the BBD block on thin interfacing (known as Trace and Toile, and similar to Swedish tracing paper).
Then I store each pattern tracing in a clear plastic sleeve in a ring binder.
I have all my ring binders labelled with which patterns are in them and it’s…[Read more]

Thanks Todd

It’s a shame because I did use it. I seem to be notorious for doubling and tripling up, even though I have a good system for paper patterns. I just didn’t want to do the same with he pdf’s. Yes going through the list of purchases is what I did do.
Thanks again.
Tamara

The Roller Skate would be a great back drop to appliquéd bunting.

@softwareandstitches I found this one https://www.craftsy.com/sewing/patterns/a-guide-to-schmetz-sewing-needles/236850 I couldn’t search for you yesterday as I was on my phone.

My favourite is size 10, It seems to sew best on my machine, a Bernina semi-industrial. I am pretty fussy about changing them after hitting a pin or 12 hours sewing time.…[Read more]

@moushka26 My apologies in not replying sooner. I have had a bereavement.

I hope your mother continues to improve.