Nicole

I think it should be fine. You might want to interface the neckline just to help it keep its shape, but a drapey fabric might be nice! I hope you’ll show us how it turns out.

Sure, you can always copy the armhole and sleeve from another pattern. It’s not an easy process, but it’s certainly possible. I hope that helps!

You can lengthen and shorten the rise and the lengthen/shorten line on the pattern piece. Tough to say how much to add–you could either measure another pair of trousers or measure your rise and add 1″ and see how that goes. You can also sew the rise longer by scooping it more in the rise as you sew, and that would be a way to alter the pair you…[Read more]

There’s another discussion here to help you: https://oliverands.com/community/forums/topic/wide-neck-adjustment

Or you could just measure the length that you want the armholes to be and cut the bias to that length and sew it into a loop…

Lots of options:
I’m sure @juliamom2009 used fold over elastic.
Or, you could make long tubes of fabric and then put elastic inside them, like gathered straps.
My daughter just requested a jumpsuit like that so she doesn’t have to re-tie the bows with every toilet break.

Ah ok, thanks Shelley. I can see that. I will give it a go!

From looking at diagrams for high/round/full bottom adjustment, I think it’s best described as an FBA for the backside.
It’s the same slash, pivot and spread as an FBA but applied to the middle(ish) part of the centre back seam.
Does that make sense?

I’m glad it worked out, and my apologies again for the silence! Thanks so much for your kind words. I’m glad you’re happy with the book and you might be interested in our first tween/teen pattern, the Girl on the Go Dress and Top for your 12-year-old daughter? Very happy you found us, and welcome to our little community!

Ok, sorry for the delay. I’m finally getting a chance to look at this. I recall changing the width of this piece several times during the development of the book, and it’s been so long now I forget exactly why I changed it. But it does indeed seem like the facing should be a little wider or the seam allowances should be trimmed a bit narrower. I…[Read more]

Sorry, not ignoring you. I’ll reply just as soon as I get a chance to look into this, ok? Wearing too many hats right now…

Looking at the instructions and pictures again, and checking the true 1″ wide facing strip, I can only conclude there’s an error…
@liesl ? It works perfectly with the instructions and illustrations if the strip were even 1/4″ wider…
Currently you sew 1/2″ inch, fold over 1/4″ and that only leaves 1/4″ to cover the seam allowances. Yet the…[Read more]

To save modifying my comment again I’ll leave the error there for posterity 🙂
I was adding up to a strip of some width other than 1″ (1&1/2″ would be the sum of 1/2″+3/4″+1/4″)
Anyway, the short answer is: trim those seam allowances aggressively and maybe fold your raw edge over by slightly less than 1/4″
Apologies for the brain fade.

For your first question about adjusting the skirt: if you took the bodice in at the side seams I would do the same with the skirt. Simply because it makes the maths simpler.

The cuff question: you’re on the right track with your stitching but you’re imagining the next step differently to where the pattern is taking you. 🙂
The raw, unstitched…[Read more]

If you’re not taking in at the armholes this should be fine. You could also consider adding waist darts similar to the Fairy Tale Dress for a closer fit. But yes, tapering to the waist is perfectly fine!

Glad it worked out! I’ve adjusted the neckline for friends by lowering as well and it’s worked out just fine. Happy New Year!

Hi Veronica,

Sorry for the silence; we’ve been laid low with the flu! In general, a longer collar band will mean lowering the neckline, but I would suggest marking the desired neckline on your muslin and measuring that first. You can probably use the collar band and collar from a different size once you know the length of the the neckline itself.…[Read more]

Hi Denise, I think you have misread the instructions but have the right idea.
You construct one set of front, side and back panels out of fabric A, then the same out of fabric B (lining). Then the hood. Then sandwich it all together and stitch the periphery before turning it through an armhole.
Which step is it that you’re reading?