Nicole

Sure, you could easily swap the buttons for snaps, no problem. I don’t know how you’d add sleeves, however. I’d suggest wearing a long-sleeved shirt underneath instead.

I was just admiring the fabrics at The Draper’s Daughter yesterday. Karen has a great eye and only selects really beautiful prints and patterns. It’s all very high quality, too. https://drapersdaughter.com/

This time of year is so busy!
Thank goodness the Champagne is fizzy.

You can do it Nicole!
My Christmas gift sewing so far: a couple of bags and a wallet using Kraft-Tex washable paper, one for my mum and the others are teacher gifts – that stuff is great fun!
I’m sewing a stencilled school bus t-shirt for my nephew and an All Day Shirt for my husband.
On the rope craft front I’ve made a dreamcatcher (shudder) for…[Read more]

That does seem a little odd to me.

I’ve checked, and the source file is spot on. I’ve just looked at it in our design software, and the box is set to be exactly 1 inch by 1 inch. And I printed the same page you have, and mine measures exactly to spec. I’m not sure why you’re having the issue you are seeing. It could be due to the printer and/or…[Read more]

You only interface ONE of the collar pieces.
For View A this will become the outer collar. The inner collar, the one that shows more when the collar is turned down as worn, is not interfaced.
For View B’s Mandarin collar it is reversed – the interfaced collar piece is on the inside.

I figured that was wrong! But I only pinned a bit like that to take a picture to ask if that’s what was meant by pin on the seam line. 🙂

I guess I just have a lot of ease. I will try it. The thing about doing a new thing… you aren’t sure you’ve done it correctly until it turns out or doesn’t and it’s “too late.” HA! But once you have the…[Read more]

The last picture is a wrong way go back 🙂 don’t do that.
The raw edges should be aligned. Raw edge of collar band facing, shirt, then collar band.
The dots (1/2″ in from ends) should align with the edges of the finished plackets. Pin those ends first. Then pin the centre notches, then side notches then keep bisecting each section with pins until…[Read more]

Hmmm, not sure quite what you mean. The flat pattern piece is only shown once in the instructions and that’s on the first page where the pattern pieces are shown numbered and named.
The only pattern piece you need for the pants is number 12: Leggings.
It is quite wide as there’s only the one piece to fully around the leg with the single seam at…[Read more]

In the pic above the green is 1/2 inch of neckline. The collar band is aligned and pinned to the basting line (where interfacing starts).

When you say pin on seamline do you mean aligning raw edge of collar band with the stitchline (basting line) like this:

This is a picture of the end where if I pin at one end and align raw edges it shows the extra.

Ugh. I need to figure out how to decrease my photo size. Grrr. Lol.

Ha! The first thing I did was say- did I pin the wrong side.

Nope!

Here is my picture.

Note I have sandwiched the shirt between the collar band and the rough edges of the band and shirt are aligned.

I’m having a hard time understanding what you mean by by pin at the seamline.

Oh, good question @lightningmcstitch! I’ve sewn the size 10 myself, so I know the collar fits correctly. When I say pin on the seamline I mean don’t pin at the edges but pin where you’ll be sewing. You’ve already staystitched the neckline, so that’s a good guide. I hope that helps! We’ve got lots of photos on the sew-along, so maybe that is a good…[Read more]

I don’t have the pattern to hand, but is there any chance you’re trying to attach the collar band upside down?

Size 10. Pinning on seam line? So what do I line up? I am confused by that!! 🙂

I am aligning rough the cut edges of the neckline and the collar band right?

I will see if I can take a small file picture to upload. Although I’ve never had any luck uploading pictures to the forum.

Can you tell me what size you’re making? It’s late here, but I can double-check it in the morning. In the meantime, make sure you’re pinning on the seamline and not on the cut line. The smaller sizes will require more clipping than the larger sizes, but if you need to clip don’t hold back. Some fabrics require more clipping than others. I hope that helps!