Oliver + S

Sew Alongs

Lisette B6244 Coat Sew Along

Viewing 15 posts - 1 through 15 (of 45 total)
  • LINK
    Todd Gibson
    Keymaster
    @todd

    The Lisette B6244 coat sew-along is scheduled for Oct. 14-16, 2015.

    Here’s where you’ll find it once it kicks off. You can start following this topic to be kept up to date.

    LINK
    Ginger @Ginger

    May we ask questions about fabric or should we wait until the sew-along begins? Thanks so much.

    LINK
    cybele727 @cybele727

    Ask now so you can be prepared to see along!

    LINK
    Ginger @Ginger

    I’ve been sewing since I was a child. But have only made a handful of things out of wool. So I’m not very familiar with the different types. I have a few wools in my stash, that were given to me, so I don’t know what type they are. Any tips for determining if any of my gifted wools would work for this coat or not? Hold it up and see if it drapes well? LOL I read Liesl’s blog post about choosing fabric but alas there are no garment fabric stores near me. Thanks so much.

    LINK
    cybele727 @cybele727

    I have no idea. I’ve never sewn wool before. Sorry… maybe someone else will jump on.

    LINK
    Lightning McStitch @LightningMcStitch

    Carnaby Cape by Handmaker's Factory @Ginger I think you’re exactly right to say “hold it up and see how it falls/drapes”. If it feels like it will be a nice warm layer and it drapes nicely then I think you’ve got your perfect fabric.
    Here’s a picture of my mum and I both wearing the same cape pattern. I love the fabric I found for her one because of the gorgeous double face, but you can see from the picture that it’s a bit stiffer and doesn’t drape quite as nicely.
    For this Lisette coat I want fabric that looks like my mum’s cape, but drapes like mine!

    LINK
    Liesl Gibson
    Keymaster
    @liesl

    Right on, @lightningmcstitch! The drape is important for this one. The fabric can be relatively thick as long as it’s not too stiff. @Ginger, I’d suggest going to a fabric store and looking at the coatings section so you can see the type of fabric we’ve recommended for this pattern. That way you’ll know what to look for when you shop your stash!

    LINK
    StemStitch @stemstitch

    Hi everyone, I am new on the forum (although have been sewing Oliver and S patterns for 3 or 4 years) and wondering what the camel fabric on the pattern envelope is? I really like the way it drapes.

    LINK
    Jen @luminosajane

    I hope I’m not behind already–I still need to trace my pattern pieces! Looking forward to this coat. And this is my first sew along!

    LINK
    Liesl Gibson
    Keymaster
    @liesl

    Hello, friends! I’m so glad you’re joining me for our Lisette coat B6244 sew-along. This is a really fast sew: with only three pattern pieces, no lining or facings, and a minimum of seams, we’ll be spending more time on flat-finishing the seams than on anything else. If you’ve never tried a flat-felled seam before, I think you’re going to like the way they look. They make the inside of the coat look as nice as the outside, which is important when you’re sewing such a simple piece.

     

    B6244sewalongTITLE

     

    Before we get started, I must apologize for the quality of the photos in the sew-along. When I sewed my coat–in early August, of course–all of our photography equipment was already en route to Spain (it still hasn’t arrived!), and I was sewing and photographing wherever and whenever I could, usually in between half-packed suitcases and overflowing boxes! But I think you’ll still be able to see all the steps clearly, and I’ll certainly talk you through everything to be sure it’s clear. Holler if anything is unclear. I’ve added lots of explanations to guide you along as well.

    Also, please note that all the steps are taken directly from the pattern guide sheets themselves, and I’ve added my additional instructions in brackets where applicable. [Like this.] OK?

    • Day 1 (today): sew the front and back of the coat
    • Day 2: add the sleeves
    • Day 3: hem and finish the coat

    Don’t forget to grab a badge for your blog or for social media. Maybe you’ll inspire a friend to sew a coat, too!

     

    B6244sewalongBadge

     

    Day 1

    Front and Back

    1. REINFORCE inner corner of FRONT (1), pivoting at inner small circle. [You’re simply using a basic straight stitch here as a stay stitch. Keep your stitch length relatively short, and use those markings you traced from the sewing pattern as your guide. Stitch to the innermost dart leg before pivoting to make a nice V shape.]

     

    fig-2

     

    Clip diagonally to inner small circle. [Yes, nerve-wracking, I know. The staystitching will keep you safe, and now you’ll be able to stitch the dart closed in the next step. That flap above the dart is the back collar, by the way.]

     

    fig-3

     

    2. Stitch dart in front between outer small circles. Press fold of dart toward side. [This is a simple dart, so don’t over-think it. Just stitch from the widest point to the narrowest and leave thread tails at the point so you can knot them instead of backstitching or lockstitching–it just gives a better result. Then use lots of steam (and a pressing cloth or a handkerchief) and press the dart take-up toward the side seam.]

     

    fig-4

    see my thread tails here before I knotted them?
     

    3. Stitch center back seam of COLLAR (which is in one with front), using a flat-fell seam as follows: [OK, in other words, sew the two collar flaps together with right sides facing each other. Easy. Then you’ll flat fell the seam as follows.]

     

    fig-5

    pressing the longer seam allowances around the trimmed seam allowance

     

    4. To make a flat-fell seam, trim right seam allowance to 1/4” (6mm). Press left seam allowance toward cut edge. Turn under 1/4” (6mm) on left seam allowance. Press. Stitch close to pressed-under edge. [Got that? Trim one of the two seam allowances to 1/4″, press the other seam allowance around the trimmed seam allowance, and then press the two seam allowances back toward the collar so the trimmed seam allowance is sandwiches and completely covered by the longer seam allowance. Then simple edgestitch the longer seam allowances along the folded edge to finish it. We’ll be doing this with all the seam allowances, so you may want to practice with a swatch until you find a stitch length that you like. A medium stitch length sometimes looks nicer than a short stitch because of the thick coating fabric. And if you have an edgestitching foot, lucky you! You’ll make good use of it here. If you don’t have one, you’re not alone–I don’t either. I just edgestitch by eye and find a spot on my presser foot or on my machine to help guide me as I sew.]

     

    fig-6

     

    5. STAYSTITCH BACK (2) neck edge between circles. [Like step 1., this is a staystitch with a regular straight stitch. Now, I didn’t do it, but I wish I had: if your fabric is very stretchy, you might want to add a length of twill tape to the staystitching to prevent stretching in the finished neckline. If you do decide to add it, refer to step 6, below where I explain how to add it to the shoulders.]

     

    fig-1

     

    6. EASESTITCH shoulder edges of back between notches and circles. [In addition to easestitching the back shoulders, I also decided to add twill tape to the front shoulders of my coat to prevent them from stretching. To do this, I basted the front shoulders at 5/8″, as instructed for the back, and I slipped a length of twill tape under my presser foot as I basted so the twill tape was caught in my basting. You can see the twill tape in the next photo. Feel free to do this to your back neck and front shoulder as well. The weight of the fabric can cause them the stretch if they aren’t reinforced.]

    7. With right sides together, pin back to front at shoulders and neck edge, matching notches, center backs and circles. Adjust ease. [The back shoulders are wider than the front, so you’re simply easing them in a bit.] Baste, clipping back neck edge 1/4” (6mm) where necessary. Stitch, breaking stitching at circles, using a flat fell seam. [Let me translate this a bit for you: Start by pinning and easing the shoulders right up to the spot where you clipped in Step 1. When you reach that little clipped V–by the dart–on the coat front, match that to the dot on the back neckline of the coat and start pinning the pin the collar to the back neckline. Chances are that you won’t need to clip anything, since your wool is probably quite malleable. But if you do clip, clip conservatively. You want to keep the back neck as intact as possible to give a nice flat-felled finish to the neckline.]

     

    fig-7

     

    8. To make a flat-fell seam, trim front seam allowance to 1/4” (6mm). Press back and shoulder seam allowances toward cut edge. Turn under 1/4” (6mm) on back and shoulder seam allowance. Press. Stitch close to pressed-under edge, pivoting stitching at inner corners. [At first this step may not seem possible, but it’s actually pretty slick. Just think of it as three different sections and fold and press each section separately, focusing on getting the corners nice and neat before you edgestitch.]

     

    fig-8

     

    9. Stitch back to front at sides using flat fell seams. [Side seams with flat-felled seams. You’ve got this. In fact, you don’t even need a photo!]

    10. To make a flat-fell seam, trim back seam allowance to 1/4” (6mm). Press front seam allowance toward cut edge. Turn under 1/4” (6mm) on front seam allowance. Press. Stitch close to pressed-under edge.

    That’s it for Day 1. You’ve already got the basic structure of the coat, can you believe it? Tomorrow we’ll add the sleeves.

    Day 2

    Hello again, and welcome to Day 2 of the B6244 Lisette coat sew-along. Today we’ll add sleeves to our coats.

    Sleeve

    11. EASESTITCH cap of SLEEVE (3) between small circles. [If you sew my Oliver + S patterns you know that I prefer two rows of basting stitches for this step: one row on either side of the stitch line. So for this sleeve I stitched my gathering stitches at 1/2″ and 3/4″. But follow whatever method works best for you here.]

     

    fig-9

     

    12. Stitch sleeve seam. [Here’s where we stitch the underarm seam. Easy peasy. But the flat-felled step on this one is a little tricky! I’ll talk about that next.]

     

    fig-10

     

    13. To make a flat-fell seam, trim back seam allowance to 1/4” (6mm). Press front seam allowance toward cut edge. Turn under 1/4” (6mm) on front seam allowance. Press. Stitch close to pressed-under edge. [Since the sleeve is narrow, even a free-arm machine will have a little difficulty reaching inside the sleeve for this step. I stitched it in two parts, working from either end toward the middle as far as I could reach. But if you simply can’t reach, don’t be afraid to skip the flat-felled seams at this step! The inside of the sleeves really won’t show, so if you prefer a simpler finishing method and want to use that instead it will be your little secret.]

     

    fig-11You can see where I broke my stitch line because I couldn’t reach any farther. Instead, I picked up at the other end and met at the center. But it was tricky, and my stitching is a little wavy as a result of the tight squeeze.

     

    14. Finish lower edge of sleeve with a 5/8” (1.5cm) NARROW HEM. [In my Oliver + S patterns I recommend stitching a 5/8″ row of basting and using that basting as a folding and pressing guide for narrow hems. Feel free to use that technique here and for the outer edge of the coat. I find that it make hemming really easy and the end result is really smooth and even.]

    15. With right sides together, pin sleeve into armhole edge, matching notches, underarm seams, small circles and large circle to shoulder seam. Adjust ease. Baste. Stitch. Stitch again 1/4” (6mm) away in seam allowances. Trim close to second stitching. Press seam allowances flat. Turn seam allowances toward sleeve. [Yes, there’s a lot of ease in the cap of the sleeve. Yes, the sleeve will fit. Just be sure you’re matching all your notches, and don’t be afraid to hand baste before you stitch. A little steam from the iron can also help to shrink out a bit of the ease. A glass of wine can also help.]

     

    fig-12

     

    That’s it for today. You’re making great progress on your coat, and I’ll see you tomorrow so we can finish up.

    Day 3

    And here we are on the last day of our very short sew-along! Today is all about hemming the coat, and there’s a lot of hemming to be done. But if you use my basting trick (see below), it will go quickly. And at least we’re not sewing a lining! Today there are just two steps, and they’re identical.

    Hems

    16. On outside, finish front and collar edges of coat with a 5/8” (1.5cm) NARROW HEM. [Again, I prefer to stitch a row of basting stitches 5/8″ from the edge and use them as a folding and pressing guide. But do what works for you here. It’s a lot of folding, pressing, and stitching. Do your best not to stretch the fabric as you work, to prevent wavy edges. You’ll do the same to finish the hem in the next step.]

     

    fig-13

     

    17. On inside, finish lower edge of coat with a 5/8” (1.5cm) NARROW HEM.

    Now, one last tip. When you’re all finished, give your coat a good steaming. Much like blocking a sweater, you’ll want to coax the wool into shape so your coat looks really professional. (See the wave in the collar of my coat, below? After the photos were taken I steamed that out. Now it looks much better–but there’s no way I’m doing another photo shoot to prove it.) I like to use a spray bottle or a wet cloth to semi-saturate the cloth, especially the edges of the coat where they may have gotten a little wavy during hemming. Then set your iron to as much steam as it can muster and blast the fabric, holding the iron an inch above the coat so it doesn’t actually touch the fabric. You can also coax the fabric back into shape with your fingers. Let the fabric relax and dry (think of is as a spa experience for the coat) before you handle it again. Be sure to give the shoulders a good steaming, too, to coax all that ease into place in the sleeve caps. And then you’re finished! I hope you are really happy with your coat. And I hope it keeps you warm and cozy this fall and winter! I’m still eagerly awaiting weather that’s cool enough for me to enjoy my coat–but it won’t be long now.

     

    Coat1

    • This reply was modified 8 years ago by Todd Gibson.
    • This reply was modified 8 years ago by Liesl Gibson. Reason: Added day 2 of sew along
    • This reply was modified 8 years ago by Liesl Gibson. Reason: Day 3 of sew along posted
    • This reply was modified 8 years ago by Todd Gibson.
    LINK
    dubhels2003 @dubhels2003

    Apologies if I have missed it, but what is Easestitching (step 6)? Is it sewing a loose large stitch that you can pull to then help ease in? I am probably being an idiot, I just don’t want ot get this wrong!

    LINK
    Liesl Gibson
    Keymaster
    @liesl

    Day 2 of the B6244 Coat sew along is now posted.

    LINK
    Liesl Gibson
    Keymaster
    @liesl

    Hi everyone! I’m out of town at a conference, so apologies for the slow replies. @dubhels2003, I think you mean easestitching? It’s a basting stitch that you can remove after you finish the seam. Easestitching allows you to shorten an edge slightly without causing puckers or gathers. How is everyone doing so far? I’m wishing I had packed my coat for this trip–it’s a bit chilly in Italy!

    LINK
    miss_sonja @miss_sonja

    I know this pattern specifies wool, but is anyone trying it with fleece? I just picked up the pattern today.

    LINK
    Liesl Gibson
    Keymaster
    @liesl

    And the final day of the sew along has now been posted. Enjoy!

Viewing 15 posts - 1 through 15 (of 45 total)

You must be logged in to reply to this topic.

copyright

Unless otherwise credited, all work on this blog is © Liesl + Co., Inc, 2008-2024. You are welcome to link to this blog, but please ask permission before using any text or images.